KEMPEROL 2K PUR PDF

KEMPEROL 2K-PUR is a two-component, UV-stable high performance seamless and self-terminating cold fluid-applied polyester reinforced solvent-free. KEMPEROL 2K-PUR Speedshot combined with KEMPEROL 2K-PUR is the ideal solution for all applications where speed is essential. These include balconies. KEMPEROL® 2K-PUR is a solvent-free and odourless, fully reinforced, polyurethane resin-based liquid waterproofing system. It is ideal for use on sustainablility.

Author: Nat Samukree
Country: Laos
Language: English (Spanish)
Genre: Video
Published (Last): 14 October 2016
Pages: 282
PDF File Size: 19.14 Mb
ePub File Size: 10.9 Mb
ISBN: 342-4-52491-586-9
Downloads: 62820
Price: Free* [*Free Regsitration Required]
Uploader: Digami

Do not flash over existing through-wall flashings, weep holes and overflow scuppers. Hunter Panels-Tapered H-Shield, 1.

Fleece shall overlap 2 inches 5 cm minimum for all joints. Roofdrain green roof drainage and water storage layer Lindum Turf. Repeat testing to verify suitability of substrate preparation.

Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction. Store materials off the ground or on pallets, under cover and in a cool, dry location, out of direct sunlight, in accordance with manufacturer’ s recommendations. Do not install products under environmental conditions outside manufacturer’s absolute limits. Provide with shim system or integral height adjustment mechanism.

Cap sheet shall be overlapped a minimum of 3 inches pue side laps and 6 inches for end laps. Aggregate will initially sink into surfacing, requiring the application of additional aggregate. Suitable for landscaped applications where a direct topping of soil or other growing media with extensive-type upr such as sedums will be planted.

Also to be used when ambient temperature is 50 degrees F 10 degrees C and below. Fleece shall be cut neatly to fit all flashing conditions without a buildup iemperol multiple fleece layers. Apply the waterproofing membrane immediately following full curing of the primer in order to obtain the best bond between primer and membrane.

  ALEX MURRAY GIORGIO AGAMBEN PDF

Broadcast aggregate to excess into surfacing until a uniform k2 aggregate layer has been achieved. Materials shall be products of a single manufacturer 2 items specified that are standard with manufacturer of cold fluid-applied polyurethane liquid resin roofing and waterproofing membrane and flashing system. Areas of minor surface deterioration of 0.

Kemperol 2K-PUR – Kemper System Ltd

Water retention mat should be channeled into an internal drain or perimeter drain system. Various Kemper warranties are available. Where results exceed the maximum acceptable reading contact Membrane Manufacturer for recommendations.

Furnish a copy of records to each party attending. Do not allow waste products containing petroleum, grease, acid, solvents, vegetable or mineral oil, animal oil, animal fat, etc.

Install overburden neatly, level and even. Sealing of air intakes with activated carbon filters. Ensure that overburden is properly supported to provide even weight distribution to underlying assembly. At all fleece seams, allow a 2 inches 5 cm overlap for all side joints and a 4 inches 10 cm overlap for all end joints. Overlap fabric in the direction of water flow. Exterior-grade plywood sheathing board, installed plugged side up, with the following characteristics:.

Pre-mix single-component and two-component coatings prior to application to achieve an even consistency. Reinforce all inside and outside corners with a 4 inch diameter conical piece of membrane prior to installing the exposed flashing layer. Roofing membranes – products from other companies. Frothing, bubbling, or pinholes within the primer indicates excessive moisture content within the substrate, beneath the surface.

  KAPITALO PAKANKAMUMAS PDF

Kemperol 2K-PUR highly permeable roofing membrane

Convene a pre-roofing conference approximately two weeks before scheduled commencement of waterproofing system installation and associated work. Application exclusively by trained and approved contractors Solvent-free and odourless Cold-applied liquid polymer Fully reinforced and fully bonded Seamless UV stable Vapour permeable Excellent elasticity and tensile strength Performance: Delete the paragraph s not required.

Schedule tests promptly to allow timely installation of protection layers.

Porous and higher moisture content concrete pug may require an adjustment to the primer application rate or multiple coats to achieve proper pore saturation and sealing. Not suitable for insulated assembly. Cold roofs Flat roofs Green roofs Warm roofs. Molded polyethylene core with water retaining troughs and openings for ventilation and evaporation, and multidirectional drainage channel system on the underside. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

Aggregate Finish Bonding Resin: Distance between joints should not exceed 20 linear feet. Use only proprietary membrane resins and materials, as pud by the membrane manufacturer.

Kemperol 2K-PUR

Store products in manufacturer’s unopened packaging with labels intact until ready for installation. Show including plans and details of cold fluid-applied two-component polyurethane waterproofing membrane system including membrane, penetration flashings, base flashings, and expansion joints size, flashing details, and attachment. Pkr and plane this compound with a squeegee and trowel to achieve a flat surface.

Author: admin